Page 61 - 无损检测2023年第十期
P. 61

王 晋, 等:

   基于双切向涡流的阵列探头设计及仿真

   过探头壳体中的调节块和弹簧, 沿探头壳体内部凹                           移动至焊缝处, 单元壳体受挤压可沿探头壳体凹槽
   槽上下滑动( 沿箭头所示方向)。为减小阵列单元与                          方向依次抬起, 8个单元壳体均可独立运动, 确保顺
   试件之间的提离距离, 弹簧始终处于压缩状态, 以保                         利通过焊缝。且通过焊缝后, 在弹簧弹力作用下, 可
   证阵列单元能够压紧在探头壳体底部。另外, 对于                           将单元壳体重新压紧在探头壳体底部, 确保探头提
   焊缝检测, 由于焊缝一般高于被检试件表面, 当探头                         离高度最小。





















                                        图8 阵列涡流探头结构示意

                                                          2010 ( 2 ): 347-351.
  4 结语
                                                      [ 7 ]  HEYZ , LUO FL , HU XC.Quantitativedefect

     提出了一种可用于检测带涂层设备的阵列涡流                                 detectionbasedon3Dma g neticfieldmeasurementof





   探头结构, 该阵列单元结构可消除直接耦合信号的                                rectan g ularp ulsededd ycurrentsensor [ J ] .Chinese



                                                          JournalofScientificInstruments , 2010 , 31 ( 2 ): 347-351.
   影响, 且可检测任何角度的缺陷, 不存在检测盲区。
                                                      [ 8 ]  YUSA N , SAKAIY , HASHIZUME H.Anedd y

       首先, 所设计探头对6~10mm 长的裂纹更敏
                                                          current p robesuitabletog aininformationaboutthe
   感, 且其信号的峰值与裂纹长度呈线性关系; 同时,
                                                          de p thofnear-sideflawsmuchdee p erthanthede p th

   探头信号的峰值位置和裂纹角度几乎呈线性关系,                                 of p enetration [ J ] .NDT &EInternational , 2011 , 44

   因此可对裂纹的长度和角度进行定量分析; 此外, 阵                               ( 1 ): 121-130.

   列单元对提离敏感, 故设计了带有弹簧的阵列探头                            [ 9 ]  徐帅. 用于 CFRP涡流检测的线圈探头耦合阻抗分

   结构, 弹簧始终处于压缩状态, 以保证检测过程中探                               析及结构设计[ D ] . 南京: 南京师范大学, 2020.

                                                     [ 10 ]  ONADI , TIAN GY , SUTTHAWEEKULR , et
   头的提离最小。
                                                          al.Desi g nand o p timisation of mutualinductance
   参考文献:
                                                          basedp ulsededd ycurrentp robe [ J ] .Measurement ,


    [ 1 ]  彭旭钊. 钢管涡流检测系统设计及孔类缺陷辨识研                        2019 , 144 : 402-409.

        究[ D ] . 南昌: 南昌航空大学, 2015.                   [ 11 ]  YEC , HUANG Y , UDPA L , etal.Differential

    [ 2 ]  李正龙. 飞机多层结构内层腐蚀涡流检测技术研究                        sensormeasurementwithrotatin gcurrentexcitation






        [ D ] . 南昌: 南昌航空大学, 2015.                         for evaluatin g multila y er structures [ J ] .IEEE






    [ 3 ]  张雯, 雷银照. 导电平板上方聚焦线圈的瞬态电磁场                      SensorsJournal , 2015 , 16 ( 3 ): 782-789.

        [ J ] . 中国电机工程学报, 2010 ( 24 ): 119-128.      [ 12 ]  XIES , DUANZ , LIJ , etal.Anovelma g neticforce

    [ 4 ]  张敬因, 雷银照. 一种具有聚焦作用的线圈涡流问题                      transmission edd y current arra y p robe and its








        解析解[ J ] . 无损检测, 2007 , 29 ( 2 ): 57-60.          a pp licationfornondestructivetestin gofdefectsin

    [ 5 ]  ZHOUD , LIY , YANX , etal.Theinvesti g ationon  p i p elinestructures [ J ] .Sensorsand Actuators A :

        theo p timaldesi g nofrectan g ularPECTp robesfor  Ph y sical , 2020 , 309 : 112030.

        evaluationofdefectsinconductivestructures [ J ] .  [ 13 ]  DAURAL U , TIAN G Y , YIQ , etal.Wireless

        International JournalofA pp liedElectroma g neticsand  p owertransfer-based edd y current non-destructive

        Mechanics , 2013 , 42 ( 2 ): 319-326.             testin g usin g a flexible p rinted coil arra y [ J ] .








    [ 6 ]  何赟泽, 罗飞路, 胡祥超, 等. 矩形脉冲涡流传感器                    Philoso p hicalTransactionsoftheRo y alSociet y A ,



        的三维磁场量与缺陷定量评估[ J ] . 仪器仪表学报,                      2020 , 378 ( 2182 ): 20190579
                                                                                                7
                                                                                               2
                                                                             2023年 第45卷 第10期
                                                                                     无损检测
   56   57   58   59   60   61   62   63   64   65   66